#
# CDROM driver configuration
#
config AZTCD
	tristate "Aztech/Orchid/Okano/Wearnes/TXC/CyDROM  CDROM support"
	depends on CD_NO_IDESCSI
	---help---
	  This is your driver if you have an Aztech CDA268-01A, Orchid
	  CD-3110, Okano or Wearnes CDD110, Conrad TXC, or CyCD-ROM CR520 or
	  CR540 CD-ROM drive.  This driver -- just like all these CD-ROM
	  drivers -- is NOT for CD-ROM drives with IDE/ATAPI interfaces, such
	  as Aztech CDA269-031SE. Please read the file
	  <file:Documentation/cdrom/aztcd>.

	  If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM
	  file system support" below, because that's the file system used on
	  CD-ROMs.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called aztcd.  If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt>.

config GSCD
	tristate "Goldstar R420 CDROM support"
	depends on CD_NO_IDESCSI
	---help---
	  If this is your CD-ROM drive, say Y here.  As described in the file
	  <file:Documentation/cdrom/gscd>, you might have to change a setting
	  in the file <file:drivers/cdrom/gscd.h> before compiling the
	  kernel.  Please read the file <file:Documentation/cdrom/gscd>.

	  If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM
	  file system support" below, because that's the file system used on
	  CD-ROMs.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called gscd.  If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt>.

config SBPCD
	tristate "Matsushita/Panasonic/Creative, Longshine, TEAC CDROM support"
	depends on CD_NO_IDESCSI
	---help---
	  This driver supports most of the drives which use the Panasonic or
	  Sound Blaster interface.  Please read the file
	  <file:Documentation/cdrom/sbpcd>.

	  The Matsushita CR-521, CR-522, CR-523, CR-562, CR-563 drives
	  (sometimes labeled "Creative"), the Creative Labs CD200, the
	  Longshine LCS-7260, the "IBM External ISA CD-ROM" (in fact a CR-56x
	  model), the TEAC CD-55A fall under this category.  Some other
	  "electrically compatible" drives (Vertos, Genoa, some Funai models)
	  are currently not supported; for the Sanyo H94A drive currently a
	  separate driver (asked later) is responsible.  Most drives have a
	  uniquely shaped faceplate, with a caddyless motorized drawer, but
	  without external brand markings.  The older CR-52x drives have a
	  caddy and manual loading/eject, but still no external markings.  The
	  driver is able to do an extended auto-probing for interface
	  addresses and drive types; this can help to find facts in cases you
	  are not sure, but can consume some time during the boot process if
	  none of the supported drives gets found.  Once your drive got found,
	  you should enter the reported parameters into
	  <file:drivers/cdrom/sbpcd.h> and set "DISTRIBUTION 0" there.

	  This driver can support up to four CD-ROM controller cards, and each
	  card can support up to four CD-ROM drives; if you say Y here, you
	  will be asked how many controller cards you have.  If compiled as a
	  module, only one controller card (but with up to four drives) is
	  usable.

	  If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM
	  file system support" below, because that's the file system used on
	  CD-ROMs.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called sbpcd.  If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt>.

config MCD
	tristate "Mitsumi (standard) [no XA/Multisession] CDROM support"
	depends on CD_NO_IDESCSI
	---help---
	  This is the older of the two drivers for the older Mitsumi models
	  LU-005, FX-001 and FX-001D. This is not the right driver for the
	  FX-001DE and the triple or quad speed models (all these are
	  IDE/ATAPI models). Please also the file
	  <file:Documentation/cdrom/mcd>.

	  With the old LU-005 model, the whole drive chassis slides out for cd
	  insertion. The FX-xxx models use a motorized tray type mechanism.
	  Note that this driver does not support XA or MultiSession CDs
	  (PhotoCDs). There is a new driver (next question) which can do
	  this. If you want that one, say N here.

	  If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM
	  file system support" below, because that's the file system used on
	  CD-ROMs.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called mcd. If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt>.

config MCD_IRQ
	int "MCD IRQ"
	depends on MCD
	default "11"
	help
	  This allows you to specify the default value of the IRQ used by the
	  driver. This setting can be overridden by passing the "mcd="
	  parameter to the kernel at boot time (or at module load time if you
	  said M to "Standard Mitsumi CD-ROM support").

config MCD_BASE
	hex "MCD I/O base"
	depends on MCD
	default "300"
	help
	  This allows you to specify the default value of the I/O base address
	  used by the driver. This setting can be overridden by passing the
	  "mcd=" parameter to the kernel at boot time (or at module load time
	  if you said M to "Standard Mitsumi CD-ROM support").

config MCDX
	tristate "Mitsumi [XA/MultiSession] CDROM support"
	depends on CD_NO_IDESCSI
	---help---
	  Use this driver if you want to be able to read XA or MultiSession
	  CDs (PhotoCDs) as well as ordinary CDs with your Mitsumi LU-005,
	  FX-001 or FX-001D CD-ROM drive. In addition, this driver uses much
	  less kernel memory than the old one, if that is a concern. This
	  driver is able to support more than one drive, but each drive needs
	  a separate interface card. Please read the file
	  <file:Documentation/cdrom/mcdx>.

	  If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM
	  file system support" below, because that's the file system used on
	  CD-ROMs.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called mcdx. If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt>.

config OPTCD
	tristate "Optics Storage DOLPHIN 8000AT CDROM support"
	depends on CD_NO_IDESCSI
	---help---
	  This is the driver for the 'DOLPHIN' drive with a 34-pin Sony
	  compatible interface. It also works with the Lasermate CR328A. If
	  you have one of those, say Y. This driver does not work for the
	  Optics Storage 8001 drive; use the IDE-ATAPI CD-ROM driver for that
	  one. Please read the file <file:Documentation/cdrom/optcd>.

	  If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM
	  file system support" below, because that's the file system used on
	  CD-ROMs.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called optcd. If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt>.

config CM206
	tristate "Philips/LMS CM206 CDROM support"
	depends on CD_NO_IDESCSI
	---help---
	  If you have a Philips/LMS CD-ROM drive cm206 in combination with a
	  cm260 host adapter card, say Y here. Please also read the file
	  <file:Documentation/cdrom/cm206>.

	  If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM
	  file system support" below, because that's the file system used on
	  CD-ROMs.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called cm206. If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt>.

config SJCD
	tristate "Sanyo CDR-H94A CDROM support"
	depends on CD_NO_IDESCSI
	help
	  If this is your CD-ROM drive, say Y here and read the file
	  <file:Documentation/cdrom/sjcd>. You should then also say Y or M to
	  "ISO 9660 CD-ROM file system support" below, because that's the
	  file system used on CD-ROMs.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called sjcd. If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt>.

config ISP16_CDI
	tristate "ISP16/MAD16/Mozart soft configurable cdrom interface support"
	depends on CD_NO_IDESCSI
	---help---
	  These are sound cards with built-in cdrom interfaces using the OPTi
	  82C928 or 82C929 chips. Say Y here to have them detected and
	  possibly configured at boot time. In addition, You'll have to say Y
	  to a driver for the particular cdrom drive you have attached to the
	  card. Read <file:Documentation/cdrom/isp16> for details.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called isp16. If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt>.

config CDU31A
	tristate "Sony CDU31A/CDU33A CDROM support"
	depends on CD_NO_IDESCSI
	---help---
	  These CD-ROM drives have a spring-pop-out caddyless drawer, and a
	  rectangular green LED centered beneath it.  NOTE: these CD-ROM
	  drives will not be auto detected by the kernel at boot time; you
	  have to provide the interface address as an option to the kernel at
	  boot time as described in <file:Documentation/cdrom/cdu31a> or fill
	  in your parameters into <file:drivers/cdrom/cdu31a.c>.  Try "man
	  bootparam" or see the documentation of your boot loader (lilo or
	  loadlin) about how to pass options to the kernel.

	  If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM
	  file system support" below, because that's the file system used on
	  CD-ROMs.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called cdu31a.  If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt>.

config CDU535
	tristate "Sony CDU535 CDROM support"
	depends on CD_NO_IDESCSI
	---help---
	  This is the driver for the older Sony CDU-535 and CDU-531 CD-ROM
	  drives. Please read the file <file:Documentation/cdrom/sonycd535>.

	  If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM
	  file system support" below, because that's the file system used on
	  CD-ROMs.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called sonycd535. If you want to compile it as
	  a module, say M here and read <file:Documentation/modules.txt>.

